- #HOW TO GET A SENTRY SAFE OPEN FOR BATTERY IS LOW CODE#
- #HOW TO GET A SENTRY SAFE OPEN FOR BATTERY IS LOW SERIES#
Wait at least 20 seconds, then reinstall the batteries and reconnect the wiring. If everything is intact, disconnect the wire from the keypad, and remove the batteries. Remove the keypad and inspect the wires to see if they have come loose, are kinked, or cut. Disconnected and/or Damaged WiringĪs with any electronic device, wiring can get disconnected and/or damaged.
#HOW TO GET A SENTRY SAFE OPEN FOR BATTERY IS LOW CODE#
Have someone else try their code to see if theirs works. Deactivated CodeĪnother possible reason your safe won’t open is your code has been deactivated. If this is the case, you will need to wait for the specified time delay period (typically 10 minutes) and re-enter your code. If this happens, wait 10 to 20 minutes, and try again.
#HOW TO GET A SENTRY SAFE OPEN FOR BATTERY IS LOW SERIES#
Depending on the type of keypad, it typically emits a rapid series of beeps. Many safes go into penalty lockout mode if too many wrong codes are entered. This will release some of the extra pressure on the bolt and should help the handle move more freely. Next, pull the handle in the opposite direction than you normally do and enter the code. Be sure that you do not kick the keypad or the handle. Turn your back to the safe, and kick the door, hard, a few times. It’s time to unleash your inner-frustrations you get to mule kick the safe. If you hear the motor trying to retract the bolt work, but the safe won’t open, a jam could be the culprit. Jammed Bolt WorkĪt times, the bolt work can get jammed for a wide variety of reasons. There may be enough power in the batteries to operate the keypad, but not enough to completely retract the boltwork. It is important to try this step first, even if your keypad beeps and lights up as normal. Off brand batteries lose power much faster than their brand-name counterparts. Five Possible Reasons Your Safe Won’t Open Dead Batteriesįingers crossed, the reason your safe won’t open is as simple as dead batteries.īefore you try anything, change the batteries using brand name batteries. Here are five common reasons why your safe won’t open, and what steps you should try before you call a technician. One of the most common troubleshooting calls we receive is: I remember one evening I received a call from manager trying to close up for the night who frantically said “My safe won’t open help!” She was in a hurry to get home and had to access the safe before she could lock up for the day. New user passcodes may be 3-6 digits long.When I was the service manager, I would occasionally cover the late shift. Press the red button, listen for a beep and then enter your new user passcode. Delete the personal access code by pressing “Prog” key and entering the five digit pre-set factory code twice.ĬHANGING YOUR PASSCODE Press the “0” button on the keypad twice.Enter a new five digit personal access code of your choice.Enter the five digit pre-set factory code twice.If you’ve forgotten your passcode, you can reset it by using a thin rod or wire to press the reset button on the inside of the door panel. Have no fear! You can still open your digital safe without a key by restoring power to the keypad so you can enter your passcode. How do you open a digital safe if you forgot the combination? How do you open a safe if you forgot the combination? Pull up on the shackle to open the lock.Insert the shackle into the lock and squeeze firmly twice to “clear” it.On the back of the lock, slide the reset lever into the “up” position.Please try resetting the lock again by following the instructions below: What do you do when your Master lock won’t open? Apply the lubricant sparingly - you need just a few drops. Put lubricant on the shackle and dial parts if your lock freezes up in the winter. Combination locks can sometimes not work when they are dirty or frozen. Why is my combination lock stuck?įix your lock by removing dust from the inside of it, lubricating it and turning the dial many times. If all else fails, you can try breaking open the lock or drilling through the override key slot. How do you reset your digital safe if you forgot the code? How do I open my safe if I forgot the combination?